GLOSSARY ENTRY (DERIVED FROM QUESTION BELOW) | ||||||
---|---|---|---|---|---|---|
|
22:17 Feb 9, 2020 |
Russian to English translations [PRO] Tech/Engineering - Metallurgy / Casting | |||||||
---|---|---|---|---|---|---|---|
|
| ||||||
| Selected response from: Oleg Lozinskiy Russian Federation Local time: 04:50 | ||||||
Grading comment
|
Summary of answers provided | ||||
---|---|---|---|---|
3 | without [blade] stubs |
| ||
2 | without blades |
|
Summary of reference entries provided | |||
---|---|---|---|
|
Discussion entries: 1 | |
---|---|
without blades Explanation: Ступицы 5 (рис. 4.2, б) сварных рабочих колес выполняются литыми, с прилитыми частями 6 лопастей (пеньками) или без них http://www.stroitelstvo-new.ru/gidroturbina/img/4-4.png 1 — направляющий подшипник; 2 — вал турбины; 3 — припасованный болт; 4 — ступица; 5 — уплотнительное кольцо ступицы; 6 — верхнее неподвижное уплотнительное кольцо; 7 — лопасть; 8 — обод; 9 — уплотнительное кольцо обода; 10 — нижнее неподвижное уплотнительное кольцо. http://www.stroitelstvo-new.ru/gidroturbina/izgotovlenie-rab... лопасть турбины f—turbine blade n https://www.linguee.com/russian-english/translation/лопасть.... |
| |
Login to enter a peer comment (or grade) |
without [blade] stubs Explanation: A comprehensive test campaign was performed in the Politecnico di Milano wind tunnel to compare the aerodynamic performances of the ERICA engine air-intake. Indeed, several operating conditions were tested i.e. cruise, conversion and hovering, with and without blade stubs for several values of flow rates of the principal and by-pass duct. ...As a matter of fact, a remarkable total pressure saving was found with the stubs-off model. Unfortunately, the presence of the rotating hub significantly reduced the gain. In fact, the total pressure is 6% higher with the optimized duct, but it must be considered that the stub blade makes much more disturbance that the real complete one as the tip of the stub, and consequently the tip vortex , is very close to the duct inlet. https://cordis.europa.eu/project/id/619949/reporting The three rotor head configurations are designated: H.1 - without blade stubs but with spacers; H2 - including both stubs and spacers; and H3 - including blade. https://www.google.ru/search?newwindow=1&biw=1067&bih=750&tb... Ref. also to: - https://www.google.ru/search?newwindow=1&biw=1067&bih=750&tb... -------------------------------------------------- Note added at 9 час (2020-02-10 08:13:25 GMT) -------------------------------------------------- В некоторых случаях при изготовлении сварных рабочих колес с целью получения высокопрочного соединения применяется электро-шлаковая приварка лопасти не непосредственно к ступице, а к пенькам, отлитым на ее поверхности, при этом шов оказывается в зоне, достаточно удаленной от места наибольших напряжений. Но при совмещении лопастей с пеньками их профили часто не совпадают и пеньки приходится подрубать или наплавлять. Кроме того, омываемую поверхность ступицы не удается обработать на станке. https://mash-xxl.info/info/337198/ |
| |
Grading comment
| ||
Login to enter a peer comment (or grade) |
21 hrs |
Reference Reference information: Дима, посмотрите рис.6 https://pdfs.semanticscholar.org/adb9/c8f05419403a05f0f0c329... I hope that helps -------------------------------------------------- Note added at 1 day 17 hrs (2020-02-11 15:49:20 GMT) -------------------------------------------------- и вот тут ещё рис.4,2 http://www.stroitelstvo-new.ru/gidroturbina/izgotovlenie-rab... |
| ||
Note to reference poster
| |||
Login to enter a peer comment (or grade) |
Login or register (free and only takes a few minutes) to participate in this question.
You will also have access to many other tools and opportunities designed for those who have language-related jobs (or are passionate about them). Participation is free and the site has a strict confidentiality policy.